How to choose the right cable: 5 things that matter more than price
You've carefully selected your amplifier and speakers, but now comes the next question: which speaker cable do you need? Some cables cost just a few euros per metre, while others are considerably more expensive. Does that price difference actually affect the sound, or are you mainly paying for the finish and materials used?
When choosing speaker cable, several characteristics matter more than the price. These include cable length, conductor cross-sectional area, material and connection quality. Particularly over longer distances or with low-impedance speakers, these factors can affect the electrical performance of your system.
We'll discuss five important considerations to help you choose a suitable speaker cable without spending more than necessary.
1. Keep your speaker cable as short as practically possible
Every speaker cable has a certain electrical resistance. This resistance increases as the cable gets longer. As a result, some of the power supplied by your amplifier is lost in the cable. With a short cable and sufficient copper cross-sectional area, this loss is usually small, but it can become more significant over longer cable runs.
An important detail is that the audio signal travels through two conductors: from the amplifier to the speaker and back again. If you connect a speaker five metres away, the total electrical conductor length is approximately ten metres. You need to account for this when calculating speaker cable resistance.
Try to keep the cable route as efficient as possible. There's no need to save every centimetre, but leaving tens of metres of unnecessary cable coiled up behind a cabinet serves little purpose. At the same time, allow enough slack so the cable isn't pulled tightly against connectors or sharp edges.
2. Calculate the correct speaker cable gauge
Speaker cable thickness is usually specified in square millimetres (mm²). This refers to the cross-sectional area of the metal conductor, not the outside diameter including insulation. The larger the cross-sectional area, the lower the electrical resistance for the same length and material.
To calculate the correct speaker cable gauge, you should primarily consider the distance between your amplifier and speaker, as well as the speaker's impedance. At lower impedances, the same cable resistance becomes relatively more significant. A 4 ohm speaker may therefore require a larger conductor cross-section than an 8 ohm speaker over a comparable cable length.
As a practical, generous rule of thumb, a 2.5 mm² copper speaker cable is suitable for many home installations with cable runs of up to approximately five metres. For longer distances or speakers with low impedance, a 4 mm² speaker cable may be worth considering. This doesn't mean thinner cables are always unsuitable: for short distances, 1.5 mm² can also work perfectly well.
What speaker cable gauge do you need?
| Cable length per speaker | Practical choice | Consideration |
|---|---|---|
| Up to 3 metres | 1.5 to 2.5 mm² | Sufficient for many home audio systems |
| 3 to 5 metres | 2.5 mm² | A generous choice for 4 and 8 ohm speakers |
| 5 to 10 metres | 2.5 to 4 mm² | Pay extra attention with 4 ohm speakers |
| More than 10 metres | Calculate the required cross-section | Impedance and desired maximum cable resistance determine the choice |
These are general guidelines for copper speaker cables, not absolute limits. The correct cross-sectional area depends on the complete installation.
How to calculate speaker cable resistance
If you want a more precise calculation, the electrical resistance of a copper speaker cable can be estimated using the following formula:
R = (2 × L × 0.0175) / A
Here, R is the cable resistance in ohms, L is the distance in metres between the amplifier and speaker, and A is the cross-sectional area of one conductor in mm². The factor 0.0175 is an approximation of copper's resistivity at room temperature. Multiplying by two accounts for the outgoing and return conductors.
Suppose you connect a speaker five metres away using a 2.5 mm² copper cable. The calculated resistance is approximately 0.07 ohms. At the same distance, a 1.5 mm² cable has a resistance of approximately 0.117 ohms. A thicker cable therefore reduces resistance, but it's important to assess whether that difference is actually relevant to your installation.
3. Pay attention to conductor material and insulation
Not all speaker cables are constructed in the same way. Alongside standard copper speaker cables, there are also versions with silver-plated copper conductors. Copper is widely used for speaker cables because of its good electrical conductivity. Silver-plated copper can also be interesting if you want to pay particular attention to the conductor's finish and durability.
Metal surfaces can oxidise when exposed to air and moisture. It's therefore worth considering not only the conductor material but also how well the cable is protected and the quality of its connections. Many people prefer silver-plated speaker cables. The properties of the silver layer can offer advantages in certain applications, although this doesn't automatically mean that every silver-plated cable delivers audibly better performance.
Insulation also plays a role. Many speaker cables use PVC, but cables with PTFE insulation, also known as Teflon, are available too. PTFE is resistant to high temperatures and various chemical influences. PTFE is often preferred because of its long-term material stability. This makes it an interesting option if you pay particular attention to material selection. However, a well-manufactured cable with PVC insulation can also provide reliable performance for many years.
4. Good connectors matter more than a luxurious cable finish
A speaker cable can have excellent electrical properties but still cause problems if its ends are poorly connected. Loose copper strands, insufficient contact pressure or corroded connections can increase contact resistance or make the connection unreliable. Secure connections are especially important in systems where components are frequently changed.
You can connect speaker cables directly to suitable screw terminals or use banana plugs or spade connectors. Banana plugs are practical if you frequently connect or disconnect equipment. Spade connectors can provide a secure connection with compatible screw terminals. The best connector depends mainly on the connections available on your amplifier and speakers.
A properly fitted connector can reduce exposure of the cable ends to air and moisture, but it cannot prevent oxidation under all conditions. Correctly connected bare copper wire can also work perfectly well. What matters most is that the connection remains clean, secure and electrically reliable.
Check the connections occasionally and make sure no loose wire strands can bridge the positive and negative terminals. Always switch off the amplifier before connecting or replacing cables.
5. Take your time comparing different speaker cables by listening
Have you chosen the correct cable gauge, kept the length reasonable and ensured reliable connections? Then you can take things a step further. Particularly if you've carefully selected your amplifier and speakers, it may be interesting to compare different speaker cables in your own system. Ultimately, it's not just about technical specifications but also about how you personally experience the sound.
Differences between speaker cables can be subtle. You might not notice anything immediately when changing cables, but listening carefully to familiar music can help you decide whether you have a preference. Take your time and pay attention, for example, to the reproduction of voices, instruments and low frequencies. Try to keep the volume and other settings the same so you can compare the cables as fairly as possible.
That doesn't mean a more expensive cable automatically sounds better. When cables have comparable electrical properties and are correctly connected, audible differences are not a given. The most important thing is to choose a cable that is technically suitable for your system and delivers a result you're happy with.
The same applies when building your own speakers using, for example, Scan-Speak drivers. In such a project, you often pay close attention to driver selection, cabinet construction and crossover design. It makes sense to choose the wiring just as carefully and perhaps compare different options. This allows you to discover which combination works best for your listening room and personal preferences.
Which speaker cable should you choose?
The best speaker cable isn't necessarily the most expensive one, but the one that suits your amplifier, speakers and installation. Start by determining the required length, then calculate which conductor cross-section is sufficient to keep cable resistance low. Choose an appropriate conductor material, check the insulation and ensure secure connections.
For many home installations, a 2.5 mm² copper speaker cable is a practical choice. For longer distances or low-impedance speakers, a thicker cable may offer advantages. Ultimately, it's about choosing the right technical characteristics rather than the highest price tag.
Are you working on a new DIY audio project or looking to improve your existing system? Explore the SoundImports range of speaker cables, connectors and quality speaker components, including Scan-Speak drivers.

New products
Home audio
Audio components
Crossover components
Test & measurement
DIY kits
Accessories
SALE
New products
Speakers
Amplifiers
DAC converters
DSP modules
Turntables
Streamers
Woofers
Tweeters
Exciters
Bass shakers
Plate amplifiers
Amplifier modules
Single board computers
Assembled crossovers
Printed Circuit Boards (PCB)
Capacitors
Resistors
Coils
Circuit Breakers
Crossover tools
Screw terminals
Acoustic measurements
Electric measurements
Sound level meters
DIY amplifier kits
DIY component packs
DIY speaker kit
DIY subwoofer kits
DIY bluetooth speaker
DIY electronics kits
Binding posts
Cabinet Hardware
Cables
Connectors
Speaker cabinets
Electromechanics
Power supplies
Speaker repair
Workshop & tools
Amplifier accessories
Stands & mounts
Gift voucher
Books
SALE









New products
Speakers
Amplifiers
DAC converters
DSP modules
Turntables
Streamers
Woofers
Tweeters
Exciters
Bass shakers
Plate amplifiers
Amplifier modules
Single board computers
Assembled crossovers
Printed Circuit Boards (PCB)
Capacitors
Resistors
Coils
Circuit Breakers
Crossover tools
Screw terminals
Acoustic measurements
Electric measurements
Sound level meters
DIY amplifier kits
DIY component packs
DIY speaker kit
DIY subwoofer kits
DIY bluetooth speaker
DIY electronics kits
Binding posts
Cabinet Hardware
Cables
Connectors
Speaker cabinets
Electromechanics
Power supplies
Speaker repair
Workshop & tools
Amplifier accessories
Stands & mounts
Gift voucher
Books
SALE





