Dayton Audio SPA250 250 Watt Subwoofer Plate Amplifier

    € 199,95 Niet op voorraad: binnen 1 week leverbaar
    Engineered to provide flexibility, ample power, and reliability, the Dayton Audio SPA250 delivers high fidelity subwoofer amplification and is tailored for home audio and home theater audio systems.... Toon meer
    • Verzending altijd verzekerd en met track & trace
    • Voor 16u besteld, vandaag verstuurd*
    • Gratis verzending vanaf €99
    • In-house technische support


    Engineered to provide flexibility, ample power, and reliability, the Dayton Audio SPA250 delivers high fidelity subwoofer amplification and is tailored for home audio and home theater audio systems.



    • Switchable 6 dB @ 35 Hz bass boost
    • Mono Class AB output stage for solid, well defined output
    • Low-level and high-level inputs connect to any system
    • Manual, auto, or triggered on/off modes for compatibility with any automated system
    • Variable gain, crossover point and switchable phase controls optimize room integration
    • Switchable 120/240V input voltage
    • Energy efficient—draws less than 1 watt in stand-by mode


    Product details

    Dayton Audio SPA250 250 Watt Subwoofer Plate Amplifier


    Bass boost or flat…you choose and the SPA250 delivers!

    The Dayton Audio SPA250 subwoofer amplifier produces 250 watts of clean power output, and combines with a host of flexible user options to make it an unbeatable choice. A user-configurable bass boost circuit creates a 6 dB peak at 35 Hz, which allows sealed subwoofer designs and certain ported enclosures to achieve their optimum bass extension and maximum "flat" output.


    Connects to almost any home audio system, and does it with ease

    The SPA250 features RCA line level and banana jack speaker level inputs and outputs, automatic power-on that is triggered by any audio input signal, and a phase reverse switch to match the subwoofer to your room and your other speakers. A single amp can accept a stereo input signal and combine it into mono, which is preferred for sub bass reproduction. A preamp or receiver's LFE output may be connected to the SPA250's Left (mono) input. The internal low pass crossover is fully adjustable between 40 and 180 Hz, and of course the amp has built-in protection against internal and external faults.


    We haven't run out of great features to talk about:

    • Variable low-pass filter at 24 dB/octave attenuation from 40 Hz ~ 180 Hz
    • Switchable phase 0° (NOR) or 180° (REV)
    • Variable gain MIN/MAX input voltage dependent
    • Speaker level high-pass outputs 6 dB/octave at approximately 180 Hz @ 4 ohms, 90 Hz @ 8 ohms (i.e. 220 uF electrolytic capacitor)
    • Line-level full bandwidth (10 Hz- 20 kHz) outputs/throughputs for adding or "daisy chaining" additional amplifiers
    • Subsonic filter 12 dB/octave high-pass filter centered at 20 Hz
    • Damping factor at rated power: 114 @ 100 Hz



    Rated power output
    <p/>1 x 252 watts at 4 ohms</br>1 x 156 watts at 8 ohms</p>
    Bridged rated power output (RMS)
    Minimum load
    4 ohms
    Signal-to-noise ratio (SNR)
    90 db
    Distortion bridged
    Amplifier classification
    Class AB
    Circuit topology
    Frequency response
    Input impedance
    10.4k ohms
    Input sensitivity
    Auto turn-on sensitivity
    ≥10 mV
    Maximum sampling rate
    Speaker output channels
    1 (+2 high level pass through channels)
    Analog in/out
    S/PDIF in/out
    AES/EBU in/out
    Coaxial in/out
    RCA in/out
    XLR in/out
    Jack in/out
    USB connection
    Network connection
    Subwoofer pre-out
    Auto on/off
    Remote control
    App control
    Equalizer (EQ) adjustment
    Equalizer (EQ) profiles
    Phase control
    check (0° or 180°)
    Crossover frequency adjustment
    Control software
    Windows/Mac compatible
    Power requirements
    115/230 VAC
    Power inlet connector
    IEC C18
    Standby power consumption
    0.29 watts (at 115 VAC)
    Current limit
    Under/over voltage protection
    Dimensions (H x W x D)
    249 x 249 x 127 mm
    Cutout dimensions
    216 x 216 mm


    5 from 5Based on 2 reviews
    Schrijf een review
    5 van 5
    De versterker bromde eerst behoorlijk toen ik hem aansloot. Heb de stekker andersom in het stopcontact gedaan en probleem opgelost. de versterker werkt prima en past precies in mijn oude subwoofer, die bliksemschade had.
    Door Geert E. on 20 November 2020
    5 van 5
    very good quality. not fitted yet though
    Door Antony E. on 26 Maart 2019

    Gerelateerde producten

    Maak uw aankoop compleet

    SPA250 250 Watt Subwoofer Plate Amplifier
    € 199,95
    SPA250 250 Watt Subwoofer Plate Amplifier
    0 Op voorraad: binnen 1 week leverbaar
    In winkelwagen
    Vergelijk 0

    Voeg nog een product toe (max. 5)

    Start vergelijking

    Door het gebruiken van onze website, ga je akkoord met het gebruik van cookies om onze website te verbeteren. Dit bericht verbergenMeer over cookies »