Dayton Audio exciters

Morel tweeters

Monacor tweeters

Scan-Speak woofers

Scan-Speak tweeters

SB Acoustics tweeters

SEAS tweeters

Alle merken

Bekijk alle merken

Incl.Excl.

BTW

Klantenservice

Nederlands

Incl.Excl.BTW

0

Sluiten

Categorieën

Filters

Bekijk alle resultaten (0)

TPA3110D2 2.1 Channel Bluetooth 4.1 Digital versterkermodule

€52,45

Toevoegen aan winkelwagen

TPA3110D2 2.1 Channel Bluetooth 4.1 Digital versterkermodule

0 reviews

Toon alle Versterker modules

2 x 15 W + 30 W

TPA3110D2 2.1 Channel Bluetooth 4.1 Digital versterkermodule

€ 43,35€ 52,45 4 Op voorraad

Gratis verzending vanaf € 99
Nu besteld, dinsdag bezorgd
Ten minste twee jaar garantie
45 dagen bedenktijd voor retourneren

Klantbeoordeling:

Vergelijk

Zakelijke offerteaanvraag

Heeft u vragen over dit product?

Onze klantenservice helpt u graag verder!

Productomschrijving

Enjoy designing your own small portable Bluetooth audio 2.1 channel DIY project with this Bluetooth 4.1 digital amplifier board. Customize the sound with built-in subwoofer, satellite, and master volume controls.

Highlights

TPA3110D2 drives stereo speakers as low as 4 Ohm with 8 to 20 VDC
Speaker Guard protection circuit system
DC detection circuit and output stage protection
More than 90% efficient for music applications
Output is fully protected against short-circuit to VCC and output to output
Both short-circuit protection and thermal protection reset automatically
Stereo lossless Bluetooth module plus noise reduction prevent internal interference

Product Details

TPA3110D2 2.1 Channel Bluetooth 4.1 Digital Amplifier Board 2 x 15W + 30W with Volume Controls

Make your own 2.1 channel small multimedia wireless Bluetooth amplifier or portable speaker with this 2 x 15W + 30W amplifier board. The board accepts 8 VDC to 20 VDC which makes it perfect for making home or mobile audio projects. Make your audio project truly portable by adding three to five 18650 Li-Ion batteries.

These boards are pre-tested and pre-assembled, which makes your project easy to complete. The on-board jacks, potentiometer, and screw terminals let you get this board powered up and playing music in minutes. Just connect your power source to the DC input screw terminals and run speaker wire from the six screw terminals to you speakers and you're done. For the most wattage output use 19 VDC power adapter. Use the 3-pin connector with 20" (508 mm) cable for internal line-in audio. Unpair your Bluetooth device and the board switches to line-in. No hiss or popping noise when searching for Bluetooth or powering on and off.

Specifications: • Power output: 2 x 15W + 1 x 30W @ 4 ohms • Impedance: 4-8Ω for satellites and 4-8Ω for subwoofer • Chip: TPA3110D2*2 • SNR: 98.8 dB • Frequency response: 20-20,000 Hz • THD+N @ Rated Power: 0.5% (2 x 13W + 30W @ 4 ohms 19 VDC) • Subwoofer Low-pass: 350 Hz 8 dB/oct, (-12 dB @750) • Channel Crosstalk: -88 dB • Signal input: 3-pin socket • Max Input Sensitivity Voltage: 525mV • Speaker output: 6 screw terminals • Power requirements: 8-20 VDC • Maximum current draw 3A • Bluetooth name and version: KRC-86, 4.1 • Dimensions (not including potentiometer): 56 mm x 15 mm x 50 mm D • Potentiometer shaft length: 15 mm without knobs.

Toon meer